AG 111 High Performance Finishing System & TractorKote AG111


Description:

Two part aliphatic specialty blend urethane.

Colors:

Gloss black, satin black, clear, reds, yellows, blues, greens, and oranges. Custom colors upon request.

Packaging:

Sold in pre-measured quarts and gallons for easy blending at the job site. Ratio is 2:1.

Uses

MasterSeries AG 111 has non-yellowing, non-chalking properties combines with excellent gloss retention and will retain a high gloss through many years of service. It is suggested, therefore, as a high performance finish in the following areas:

MasterSeries AG 111 can be applied over a wide variety of prepared and primed substrates including structural steel, cold rolled steel, aluminum, concrete, wood, plastics, and galvanized steel. In some cases, it is self-priming but is generally used as a top coat over MasterSeries permanent rust sealer/surfacer/primer.

TEST DATA

SALT SPRAY, 5% (ASTM B117)

2 coats MasterSeries permanent rust sealer primer and one coat AG 111 finish coat applied to a rusted panel and scribed with an "x" through center plate. After 14,000 hours of exposure only slight undercutting at spots along the "x" was noted and this was less than 1/32 undercut. Total film thickness 8.0 mils approximate.

OUTDOOR EXPOSURE: Two coats MasterSeries silver permanent rust sealer, one coat AG 111 argent blue applied to the Pittsburgh Homestead High Level Bridge. At the end of 14 years, less than 5% corrosion was noted.

Tabor abrasion (CS-17 1000 gms.)

1000 cycles 15 mgs.
Pencil hardness 2 H
Flexibility (ASTM D-222) Pass 1/8"mandrel bend
MEK Double Rubs, 48 hr. cure Pass 100
Gardener Impact 160 in. lbs. direct and reverse



CHEMICAL RESISTANCE

EXCELLENT

90 days immersion

Hydrochloric Acid 10% Ethylene Glycol
Sulfuric Acid 10% Ethyl Acetate
Nitric Acid 10% Methyl Ethyl Ketone
Caustic Soda 40% Methyl Isobutyl
Ketone Ammonium Chlorate 30%
Perchloroethytlene
MIL-E 23699 Hydr. Oil Tricresyl Phosphate
Oxalic Acid 10% Skydrol A500
Citric Acid JP-4 Jet Fuel
Gasoline
Sodium chloride 10%
Ammonium chloride 30%
Mil-e-23699 Hydraulic oil
Oleic acid
Skydrol A500
JP4 jet fuel
Tricresyl phosphate


GOOD

60 days immersion

Tolulene Sulphuric Acid 30%
Xylene Phosphoric Acid 50%
Methanol Lactic Acid 85%
Ethanol Oxalic Acid
Acetone FAIR
Ammonia 10%
Formic acid 10%

POOR
less than 30 days immersion
Methylene Chloride



RATING SYSTEM

90 days immersion is excellent, 60 days is good, 30 days is fair. Tests were run in total immersion.



Surface Preparation

New metal surfaces should be cleaned of oil, grease, and dirt. To obtain optimum results, the metal should be sandblasted and MasterSeries urethane primer applied then topcoated with MasterSeries AG 111 if metal surface is rusted and sadlblasting is not practical from an application or coast standpoint. MasterSeries urethane primer can be applied directly over rust which is tightly adherent. Although this situation is not as ideal as sandblasting, excellent results have been obtained. When painting over previously painted surfaces,a spot test should be made to check for lifting, or incompatibility with the old coating. Scuff old paint with 280 grit before painting. If MasterSeries silver primer has hardened beyond 7 days, scuff with 280 grit to ensure adhesion. It is extremely important that this surface is free of all moisture prior to coating application or blistering of paint film may occur.

WARNINGS: Keep out of reach of children. Harmful or fatal if swallowed. Vapor harmful. Use with adequate ventilation. Avoid contact with skin. Combustible. Keep away from heat and open flame. Close container after use. Avoid contact with eyes and skin. In case of eye contact flush immediately with plenty of water for 15 minutes. CALL A PHYSICIAN. In case of skin contact wash thoroughly with soap & water.

COMBUSTIBLE. Use only with adequate ventilation. If engineering and administrative controls of contaminants are not feasible wear a vapor/particulate respirator such as #8711 manufactured by 3M Co. or equivalent during application and until work area has been exhausted of all vapor and spray mist. Individuals with chronic respiratory problems or prior respiratory reactions to isocyanates must not be exposed to vapors or spray mist containing isocyanates. If affected by inhalation of vapor or spray mist, remove to fresh air. If breathing difficulty persists or occurs later, consult a physician and have label information available.

CONTAINS AROMATICPOLYISOCYANATE PREPOLYMER, MAY CAUSE LUNG IRRITATION AND ALLERGIC RESPIRATORY REACTION.